Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable AC Installation Across Kenmore
AC installation in Kenmore typically runs $3,500-$7,500 for a complete system, and every job starts with a free in-home estimate where we measure your space, inspect your existing ductwork, and hand you a written price before any work begins. Call (817) 402-2972 to schedule yours.
We’re the AC Installation team at Coldharbour Heating & Air, and we’ve spent years working in the homes that line Kenmore’s north Lake Washington shoreline and the streets near the Sammamish River delta. Victor Mancini built this operation in 2003 as part of the Kingswell network of independently owned HVAC businesses, and our dispatch is coordinated from our New York City office with crews serving Kenmore directly. We know the slab-and-pier ranches off Juanita Drive, the split-levels near Bastyr University, and the low-lying streets where the water table rises each winter. That local knowledge changes how we install your system, because a condenser pad that works in Bothell may sit underwater here.
Why Coldharbour Heating & Air Is Kenmore’s Preferred AC Installation Company
Kenmore homeowners call us because we show up in the window we promise, and we put our guarantee in writing before the technician leaves. Our 365-Day Done Right Promise means if any repair fails within a full year, we come back and correct it at no charge. That’s not a verbal handshake; it’s on paper every time.
Our technicians are background-checked, uniformed, and trained on nine major residential brands including Goodman, Rheem, and York. When you call (817) 402-2972, a live person answers the phone 24 hours a day, 7 days a week. No voicemail trees. No “call back in the morning” when your system quits on a Saturday night.
We understand Kenmore’s specific challenges: the persistent fog rolling off Lake Washington, the crawlspaces that never fully dry, the condenser pads that settle into muck after a wet season. Our AC Installation in Kenmore includes pad elevation and vapor barrier work as standard scope when conditions demand it, not as an add-on sales pitch.
Furnace Installation in Kenmore
Furnace Repair - Kenmore and installation addresses a specific local need: many of the city’s post-WWII through 1970s ranch and split-level homes were built with oil furnaces or electric baseboard heat, and owners are now converting to modern gas or electric forced-air systems. A typical furnace installation in Kenmore runs $3,500-$7,500, which includes the unit, necessary duct modifications, permit coordination, and our written 365-Day Done Right Promise.
From Oil or Baseboard to Modern Forced Air
Converting an older Kenmore home from oil heat or electric baseboard requires more than swapping equipment. We often need to design duct runs through crawlspaces or attics that were never built for airflow, seal every joint against the moisture that pervades this riverside city, and size the furnace correctly for a structure that may have minimal insulation by modern standards.
Moisture-Resistant Installation Practices
Kenmore’s ground-level humidity accelerates corrosion on heat exchangers and blower cabinets. We specify galvanized or coated components where standard steel would rust, and we always verify that crawlspace air handlers sit on proper risers with vapor barriers beneath. A furnace sitting in damp conditions will fail early, no matter how good the brand.
HVAC Installation in Kenmore
HVAC Installation in Kenmore encompasses the full replacement or first-time installation of heating and cooling equipment in homes that may never have had central air, or in homes where the original system has succumbed to decades of moisture and age. A complete HVAC installation in Kenmore typically costs $3,500-$7,500 depending on system type, ductwork condition, and whether we are retrofitting a home that started life with oil or baseboard heat.
Heat Pump Conversions for Kenmore’s Climate
Heat pumps excel in Western Washington’s moderate temperatures, and modern cold-climate models handle Kenmore’s occasional freeze without backup strips. We size these systems carefully because an undersized heat pump will run constantly during the long wet season, while an oversized unit short-cycles and fails to dehumidify, a real problem in a city where the air already carries lake and river moisture.
Whole-System Design for River-Delta Conditions
Every HVAC installation we perform in Kenmore includes assessment of the outdoor pad elevation, electrical disconnect condition, and crawlspace moisture levels. The Sammamish River delta’s seasonal high water tables mean we regularly find equipment that has been compromised by standing water. We fix that before the new system goes in, because installing premium equipment on a failing foundation is a waste of your money.
Trusted Brands We Service in Kenmore
Our technicians carry training certifications for Goodman, Rheem, York, and Daikin systems, and we maintain relationships with regional distributors to source parts quickly for Kenmore homeowners. Goodman offers strong value for the budget-conscious family in a 1960s ranch off 68th Avenue NE. Rheem and York provide proven reliability for homes that see heavy use through both heating and cooling seasons. Daikin’s inverter-driven heat pumps handle the variable loads of Kenmore’s mild but damp climate with particular efficiency. We don’t push one brand over another; we match the equipment to your home’s size, your ductwork’s condition, and your long-term plans. Every installation comes with our written price upfront and the Kingswell Guarantee’s five written promises: say the price before the work, show up in the window given, leave the place cleaner than found, put the guarantee in writing, and come back if it fails.
Common AC Installation Problems We See in Kenmore Homes
- Settled or flooded condenser pads in low-lying delta neighborhoods. The streets near the Sammamish River routinely see seasonal high water tables, and concrete pads sink or tilt over time. A new AC unit installed on a compromised pad will vibrate excessively, strain refrigerant lines, and sit in corrosive standing water.
- Surge-damaged electrical components after power outages. Kenmore’s tree-lined streets and exposed shoreline mean frequent outage events. Restarting a system without checking the capacitor, contactor, and electrical disconnect can send voltage spikes straight into a new compressor, voiding warranties and destroying equipment.
- Unsealed crawlspace ductwork in slab-and-pier homes. The persistent humidity in Kenmore’s crawlspaces condenses on cold duct surfaces, promoting biological growth and robbing airflow through leaks. New ductwork installed without proper sealing and insulation will lose static pressure and deliver musty air.
- Undersized vapor barriers beneath air handlers. We regularly find existing air handlers sitting on bare dirt or thin plastic sheeting that has torn. Without a proper 6-mil vapor barrier and adequate elevation, the new evaporator coil’s drain pan and surrounding cabinetry will corrode within seasons.
Pricing for AC Installation in Kenmore, NY
| Service | Typical Range in Kenmore |
|---|---|
| AC Installation (complete system) | $3,500-$7,500 |
| AC Repair (post-outage or flood restart) | $150-$650 |
| Furnace Installation | $3,500-$7,500 |
These ranges reflect what we see in Kenmore’s market, where the prevalence of older homes with minimal existing ductwork often pushes jobs toward the higher end. A straightforward replacement in a home with good ducts and a sound pad may land near $3,500. A full conversion from baseboard heat with new duct design, pad reconstruction, and vapor barrier work will trend higher. We measure every home individually, and we hand you a written fixed price before any equipment moves. That price does not change at the door. Financing paperwork and available utility rebates are handled as part of our standard process. Call (817) 402-2972 for your free estimate.
We Also Serve Cities Near Kenmore
Our crews work throughout the greater area, including Kenmore and the nearby communities of Brooklyn, Queens, Manhattan, and Staten Island. Scheduling and dispatch are coordinated from our New York City office, with local technicians serving each area directly.
Serving Kenmore, NY - Our Local Coverage Area
We’re based in the Kenmore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About AC Installation in Kenmore
No. A flooded condenser must never simply be switched back on. Water inside the electrical compartment can create a short that damages the compressor, capacitor, and contactor, and moisture in the refrigerant system contaminates the entire circuit. We check the electrical disconnect, test the capacitor, verify the refrigerant charge, and inspect the condenser coil for corrosion before any restart. In Kenmore’s delta neighborhoods, we also re-elevate the pad and improve drainage as part of the recovery. Call (817) 402-2972 and we’ll send a technician to assess it safely.
Kenmore’s persistently wet crawlspaces, fed by Lake Washington shoreline humidity and high seasonal water tables, destroy unprotected ductwork and air handlers. New equipment installed without sealing and vapor barriers will lose airflow to leaks and grow biological contamination on damp surfaces. We include this work as standard scope when conditions demand it, because installing a new system on failing infrastructure produces failing results.
Power fluctuations during outages can damage the capacitor, contactor, and control board in even a brand-new system. We recommend surge protection on every installation in Kenmore, where tree-related outages and shoreline weather events are common. If you’re running a generator, it must be properly sized and grounded to avoid voltage irregularities that can destroy a compressor. We review your electrical situation during every estimate and specify appropriate protection.
SEER2 measures cooling efficiency under more realistic conditions than the older SEER standard, including part-load operation that matches Kenmore’s mild summer peaks. In our damp climate, we also prioritize systems with strong latent heat removal, the ability to pull moisture from the air. A high SEER2 unit with poor dehumidification will leave your home clammy. We specify equipment that balances efficiency with moisture control for this specific environment.
Yes, and this is one of the most common jobs we perform in Kenmore’s 1950s-1970s housing stock. A modern cold-climate heat pump provides both heating and cooling, replacing your oil tank or baseboard system with a single efficient unit. We design ductwork for homes that never had it, coordinate removal of old equipment, and handle the full installation as one scheduled project. Most conversions fall in our standard $3,500-$7,500 range depending on duct complexity. Call (817) 402-2972 for a free in-home assessment.
Ready to replace your AC or convert your older Kenmore home to modern, efficient cooling? Call Coldharbour Heating & Air at (817) 402-2972 for a free estimate. We’ll measure your home, inspect your existing system and site conditions, and hand you a written price before any work begins. Our technicians are background-checked, uniformed, and trained on Goodman, Rheem, York, and Daikin systems. Every installation is backed by our 365-Day Done Right Promise in writing, and a live person answers our phones 24 hours a day, 7 days a week.
Written by Victor Mancini, Owner at Coldharbour Heating & Air, serving Kenmore since 2003.